Coniche shafts & key + taper

The place for Fairline discussions!
  • Advertisement

Coniche shafts & key + taper

Postby Johno » Wed Apr 04, 2018 7:04 pm

I have a 1990 corniche with tamd 41b engines are the shafts & taper + key way standard sizes as had boat out 4 antifouling and props are no good there four bladed 20x26 they have put boat back in the water as he said couldnt get props off and my time slot was up has anybody got any information on this thx john
Johno
 
Posts: 3
Joined: Tue Apr 03, 2018 4:45 pm

Re: Coniche shafts & key + taper

Postby Ribsta » Wed Apr 04, 2018 9:59 pm

Hi John,
I can’t guarantee it’s the same as yours but my boat is a Corniche 1991 with TAMD41B, also with 20x26 props. As far as it all looks it’s all standard as was supplied new.
If you PM me your email address I can email the drawing over.
Regards,
Lee
Last edited by Ribsta on Wed Sep 05, 2018 8:55 am, edited 1 time in total.
Ribsta
 
Posts: 27
Joined: Mon Apr 24, 2017 9:22 pm
Boat: Corniche 31

Re: Coniche shafts & key + taper

Postby Johno » Sat Apr 07, 2018 2:50 pm

Thx lee my email jdp2580@icloud.com
Johno
 
Posts: 3
Joined: Tue Apr 03, 2018 4:45 pm

Re: Coniche shafts & key + taper

Postby dickythe diver » Sat Apr 07, 2018 5:29 pm

Hi John, I have this year removed both my props. I used a hydraulic prop puller and blow torch, they both came of in a couple of minutes. Regards Richard.
dickythe diver
 
Posts: 19
Joined: Sun Oct 04, 2015 5:56 pm

Re: Coniche shafts & key + taper

Postby Johno » Sat Apr 07, 2018 5:53 pm

Was that on a corniche Richard and thx 4 the reply
Johno
 
Posts: 3
Joined: Tue Apr 03, 2018 4:45 pm

Re: Coniche shafts & key + taper

Postby Ribsta » Sun Apr 08, 2018 10:21 am

Hi John,
Email sent with shaft details.
Regards,
Lee
Ribsta
 
Posts: 27
Joined: Mon Apr 24, 2017 9:22 pm
Boat: Corniche 31

Re: Coniche shafts & key + taper

Postby Ribsta » Sun Apr 08, 2018 10:27 am

Where will you go for the new props?
Last edited by Ribsta on Wed Sep 05, 2018 8:55 am, edited 1 time in total.
Ribsta
 
Posts: 27
Joined: Mon Apr 24, 2017 9:22 pm
Boat: Corniche 31

Re: Coniche shafts & key + taper

Postby Gerry W » Wed Apr 25, 2018 10:13 pm

I’d be interested if you could share the taper sizes as I’m looking for a spare set of props. I’m currently running 20x26 four blades and have acheived 27.2 knots at 3900rpm on gps
If you could forward the taper sizes to gwatt20000@yahoo.co.uk i would appreciate it.
Thanks
Gerry W
 
Posts: 12
Joined: Thu Dec 11, 2014 8:45 pm

Re: Coniche shafts & key + taper

Postby dickythe diver » Mon Apr 30, 2018 10:34 pm

Hi John, No that was on a Phantom 43. I used Hamble propellers to do the work on mine, they did a brilliant job.
dickythe diver
 
Posts: 19
Joined: Sun Oct 04, 2015 5:56 pm


Return to Fairline Forum

Who is online

Users browsing this forum: Google [Bot] and 48 guests

  • Advertisement