Corniche anodes

The place for Fairline discussions!
  • Advertisement

Corniche anodes

Postby ColinK » Sat Apr 16, 2016 7:43 am

Hello all,
Well Summer is on its way and looking forward to the season. Daughter has GCSE's. so tense time but I understand once she takes her last exam and has the traditional "prom" night then we are free.
I am planning a lift quite late and this will be my first with her. Wonder if anyone knows how many and what size anodes my Corniche may have (shaft driven) I have found two points in the Lazarette where lots of black wires go to and the bolts there are 9" apart.

Cheers. Colin.
ColinK
 
Posts: 76
Joined: Sun Jan 04, 2015 12:14 am
Boat: Corniche

Re: Corniche anodes

Postby superheat6k » Sat Apr 16, 2016 10:11 pm

Colin

A couple of 4kg bar anodes. Measure the precise centres between the bolts 200mm (~8") is very common.

Check the resistance from props and P brackets to the anodes is below 1 ohm.
Failed Yachtie !!!
superheat6k
 
Posts: 246
Joined: Wed Jul 27, 2011 8:43 pm
Boat: Fairline Turbo 36

Re: Corniche anodes

Postby talltim » Mon Apr 18, 2016 7:51 pm

A per above plus mine has a disc anode on each trim tab

Don't forget the engine anodes which can be changed anytime
talltim
 
Posts: 27
Joined: Sun Dec 09, 2012 7:05 am

Re: Corniche anodes

Postby ColinK » Mon Apr 18, 2016 8:36 pm

Thank you chaps but. Aaaaaaaaah

Engine anodes where are they ?

Cheers, Col.
ColinK
 
Posts: 76
Joined: Sun Jan 04, 2015 12:14 am
Boat: Corniche

Re: Corniche anodes

Postby talltim » Tue Apr 19, 2016 6:12 pm

one in each heat exchanger

look for a square head plug, the anode screws onto the plug

dependant on engine year you could also have same fitted to intercooler and/or gearbox oil cooler
talltim
 
Posts: 27
Joined: Sun Dec 09, 2012 7:05 am

Re: Corniche anodes

Postby ColinK » Thu Apr 21, 2016 9:44 pm

Wow thanks chaps I know my next job.

I am confused by the size of the external annodes. Remeasured the bolt centres in the lazarette and they are def 9" centres and all the ones that I can find are 8". Any ideas?

Cheers, Col.
ColinK
 
Posts: 76
Joined: Sun Jan 04, 2015 12:14 am
Boat: Corniche

Re: Corniche anodes

Postby talltim » Sat Apr 23, 2016 2:03 pm

Hi Colin

Usually the hull anodes have slot rather than holes to allow some slight tolerance when fitting

On mine I found the readily available bar anodes, and relevant backing pad fitted just fine
talltim
 
Posts: 27
Joined: Sun Dec 09, 2012 7:05 am

Re: Corniche anodes

Postby superheat6k » Sat Apr 23, 2016 10:08 pm

Use one of the original mounts and drill a new one either fwd or aft to suit.

Engine assuming VP TAMD Oil cooler; Gearbox oil cooler; After cooler

Do not forget to do these as new cooler are way over priced and essential
Failed Yachtie !!!
superheat6k
 
Posts: 246
Joined: Wed Jul 27, 2011 8:43 pm
Boat: Fairline Turbo 36

Re: Corniche anodes

Postby ColinK » Sat Jul 02, 2016 1:53 pm

Howdee chaps,
Hope everyone is having a good Summer so far? We are being lifted out on 14th for a week so fingers crossed I have got to decide on what type of antifoul and chech the dreaded anodes.
I contacted a supplier of anodes today and asked him about the odd spacing on mine (9"). He said that yes he stocks them but they are huge much bigger than you would normally put on a boat my size. Now I guess that I have my fingers crossed as the chap that I bought the boat off said that he had just changed them so about 16 months ago although do bigger anodes last longer?

All the best, Colin.
ColinK
 
Posts: 76
Joined: Sun Jan 04, 2015 12:14 am
Boat: Corniche

Re: Corniche anodes

Postby ColinK » Sat Jul 23, 2016 10:20 pm

Hello chaps,
Always try and report back so now I have had my lift out can advise on my anodes

The 9" centres on my Corniche are original by the looks of it and are 12kg anodes rather than the 8kg 8" centre ones according to the anode maker.

In the end they were only a third worn so ok for a nother year. The 2kg ones on my trim tabs were gone so just managed to get 4kg lumps to fit.

Happy Summer. Col.
ColinK
 
Posts: 76
Joined: Sun Jan 04, 2015 12:14 am
Boat: Corniche

Re: Corniche anodes

Postby geotechnic » Mon Aug 08, 2016 7:50 pm

Hi

The anodes on my Corniche are 7kg 9"(227mm)centres and use 16mm bolts, anodes direct do a suitable model, normally get 2-3 years out of them
geotechnic
 
Posts: 60
Joined: Fri Apr 16, 2004 8:42 pm
Boat: Fairline Corniche

Re: Corniche anodes

Postby ColinK » Tue Aug 09, 2016 8:31 pm

Hello,
Two/three years would be great fingers crossed. Are anodes direct near Levington? Where have you got to this year we have just had 10 days on board boat went fab except......... Wouldnt go on the plane aaah.

Cheers, Col.
ColinK
 
Posts: 76
Joined: Sun Jan 04, 2015 12:14 am
Boat: Corniche

Re: Corniche anodes

Postby geotechnic » Tue Aug 09, 2016 8:42 pm

Hi Colin

Just come back down the Thames, good weather most of the time which makes a change.

This is a link to anodes direct, delivery is quite reasonable

https://anodesdirect.co.uk/joomla/index ... &Itemid=55
geotechnic
 
Posts: 60
Joined: Fri Apr 16, 2004 8:42 pm
Boat: Fairline Corniche


Return to Fairline Forum

Who is online

Users browsing this forum: Bing [Bot], Bolero, Google [Bot], Yahoo [Bot] and 30 guests

  • Advertisement