Search found 226 matches

Return to advanced search

You can buy little teak plugs for this which you trim off as required. Please don't use coloured filler from a tube, that would be so knaff.
by ms
Thu Mar 15, 2012 9:46 pm
 
Forum: Fairline Forum
Topic: removing wooden trims
Replies: 5
Views: 2900

I have bought from these people and cut, shaped myself.
saw, abrasives, drill .... it was straightforward.

http://www.plasticonline.co.uk/
by ms
Mon Feb 27, 2012 11:39 am
 
Forum: Fairline Forum
Topic: Chart table cover
Replies: 2
Views: 2171

well if someone knows all these websites for Fairline parts I would very much like to know .... Ive been a Fairline owner for 10 years and never found them.
by ms
Wed Feb 01, 2012 5:28 pm
 
Forum: Fairline Forum
Topic: Targa 27 Engine Bay Door Strut
Replies: 3
Views: 2584

I used VALTRAR SUPPLIES LIMITED, Birmingham after getting advice on the correct model from Stabilus - the manufacturer of the strut. The 'power' of the replacement strut is critical. You will find serial numbers on your old strut plus a reference to 'N' eg .... 200N this means 200 Newtons .. this is...
by ms
Tue Jan 31, 2012 12:08 pm
 
Forum: Fairline Forum
Topic: Targa 27 Engine Bay Door Strut
Replies: 3
Views: 2584

I dont have these petrols but I know that there is a 'technique'. The carbs have no choke so you have to pump(open/close) the throttle 2 or 3 times to get the carb throttle pump to deliver a little extra fuel. Take of the distributor cap and remove any moisture - a common problem on petrols after a ...
by ms
Tue Jan 31, 2012 12:02 pm
 
Forum: Fairline Forum
Topic: Winter engine starting problem - AQ145a's
Replies: 4
Views: 2719

Perhaps the secret is to re-name the boat when it is not in the water ?!
by ms
Sun Dec 04, 2011 7:59 pm
 
Forum: Fairline Forum
Topic: Reaction from the gods during re-naming?
Replies: 2
Views: 2108

I believe that 'Silver Dream' a Broads based Mirage has been under at Ludham , but I bet it was scary.
Ludham is 8ft 6 clearance I think. I would research this question very carefully.
by ms
Sun Dec 04, 2011 7:58 pm
 
Forum: Fairline Forum
Topic: ludham bridge and mirage height
Replies: 3
Views: 2554

These can also be bought from Seals Direct

I recommend - Take a photo of what you want and the profile of the extrusion and get it to Fairline.
by ms
Fri Dec 02, 2011 11:20 pm
 
Forum: Fairline Forum
Topic: Rubber strip Fairline Targa 30
Replies: 10
Views: 6670

aha .. .well done captain .......
by ms
Tue Nov 29, 2011 2:40 pm
 
Forum: Fairline Forum
Topic: Sea strainer nut forAQ130D
Replies: 9
Views: 6414

You get it from Fairline.
by ms
Sun Nov 27, 2011 10:53 am
 
Forum: Fairline Forum
Topic: Rubber strip Fairline Targa 30
Replies: 10
Views: 6670

ah knurled nut .. well that will be a bit harder You will prob have to get someone to make one for you (someone with a lathe who can do knurling .. or you might be able to get hold of a wing nut which will do the job. how frustrating .... so where is the original ? ... have you had a good rummage ar...
by ms
Thu Nov 24, 2011 5:05 pm
 
Forum: Fairline Forum
Topic: Sea strainer nut forAQ130D
Replies: 9
Views: 6414

concur with superheat only use Halfords or Screwfix nuts to work out what the thread is. Screwfix do supply stainless nuts but I don't think they are suitable for marine use. Quite honestly this is almost the sort of part that a marine engineer would have lurking in his 'useful bits and pieces' box.
by ms
Thu Nov 24, 2011 9:47 am
 
Forum: Fairline Forum
Topic: Sea strainer nut forAQ130D
Replies: 9
Views: 6414

Perhaps you could get some assorted nuts from Halfords or Screwfix and see what fits ? ... then you will know what thread is required.
by ms
Tue Nov 22, 2011 5:24 pm
 
Forum: Fairline Forum
Topic: Sea strainer nut forAQ130D
Replies: 9
Views: 6414

Have no experience with snap davits
but
Howells at Cobbs Quay, Poole are 'big in teak' and very helpful.
http://www.kjhowells.com
by ms
Fri Oct 28, 2011 9:43 pm
 
Forum: Fairline Forum
Topic: Snap davits
Replies: 4
Views: 2834

There are comments on this forum from people with Corniche with bowthruster so this would suggest that teh advice you have been given is not accurate.
by ms
Fri Oct 21, 2011 6:52 pm
 
Forum: Fairline Forum
Topic: Bow Thrusters
Replies: 8
Views: 4968
PreviousNext

Return to advanced search

  • Advertisement
cron